【OpenHarmony开源贡献者计划2022】master分支 bearpi_hm_micro 编译后生成的固件，无法正常引导系统。

**【模块名_概率】简要描述：**
参考 master 的指导文档
https://gitee.com/openharmony/device_board_bearpi/blob/master/bearpi_hm_micro/docs/device-dev/BearPi-HM_Micro%E5%BC%80%E5%8F%91%E6%9D%BF%E7%BC%96%E8%AF%91%E8%B0%83%E8%AF%95.md

bearpi_hm_micro 编译后生成的固件，无法正常引导系统。

**【环境信息】:** 
- 网络环境
- 硬件开发板型号
- 软件版本信息或tag节点
  master 分支
- 测试环境
  win11 + wsl ubuntu20.04
- 其他

**【预置条件】:**

**【测试步骤】：**

1. 
```
hb set
```
选择 bearpi_hm_micro

2. 
```
hb build -t notest --tee -f
```

3. 将编译后的文件烧录到 bearpi_hm_micro 开发板

4. 验证是否正常启动

**【预期结果】：**
可以正常启动到UI界面

**【实际结果】：**
内核启动失败，并不停重启，串口日志如下

```
NOTICE:  CPU: STM32MP157AAC Rev.Z
NOTICE:  Model: STMicroelectronics custom STM32CubeMX board - openstlinux-5.10-dunfell-mp1-21-03-31
INFO:    Reset reason (0x14):
INFO:      Pad Reset from NRST
INFO:    Using EMMC
INFO:      Instance 2
INFO:    Boot used partition fsbl1
NOTICE:  BL2: v2.2-r2.0(debug):
NOTICE:  BL2: Built : 14:41:10, Mar 16 2022
INFO:    Using crypto library 'stm32_crypto_lib'
INFO:    BL2: Doing platform setup
INFO:    RAM: DDR3-DDR3L 16bits 533000Khz
INFO:    Memory size = 0x20000000 (512 MB)
INFO:    BL2 runs SP_MIN setup
INFO:    BL2: Loading image id 4
INFO:    Loading image id=4 at address 0x2ffeb000
INFO:    Image id=4 loaded: 0x2ffeb000 - 0x2ffff000
INFO:    BL2: Loading image id 5
INFO:    Loading image id=5 at address 0xc0100000
INFO:    STM32 Image size : 817597
INFO:    Image id=5 loaded: 0xc0100000 - 0xc01c79bd
WARNING: Skip signature check (header option)
NOTICE:  ROTPK is not deployed on platform. Skipping ROTPK verification.
NOTICE:  BL2: Booting BL32
INFO:    Entry point address = 0x2ffeb000
INFO:    SPSR = 0x1d3
INFO:    Cannot find st,stpmic1 node in DT
NOTICE:  SP_MIN: v2.2-r2.0(debug):
NOTICE:  SP_MIN: Built : 14:41:11, Mar 16 2022
INFO:    ARM GICv2 driver initialized
INFO:    Set calibration timer to 60 sec
INFO:    ETZPC: UART1 (3) could be non secure
INFO:    ETZPC: SPI6 (4) could be non secure
INFO:    ETZPC: CRYP1 (9) could be non secure
INFO:    SP_MIN: Initializing runtime services
INFO:    SP_MIN: Preparing exit to normal world

U-Boot 2020.01-stm32mp-r2 (Mar 28 2022 - 14:48:32 +0800)

CPU: STM32MP157AAC Rev.Z
Model: STMicroelectronics custom STM32CubeMX board - openstlinux-5.10-dunfell-mp1-21-03-31
Board: stm32mp1 in trusted mode (st,stm32mp157a-bearpi-hm_micro-mx)
DRAM:  512 MiB
phy_power:  no phy-power?
Clocks:
- MPU : 650 MHz
- MCU : 208.878 MHz
- AXI : 266.500 MHz
- PER : 0 MHz
- DDR : 533 MHz
NAND:  0 MiB
MMC:   STM32 SD/MMC: 2, STM32 SD/MMC: 0, STM32 SD/MMC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment

invalid MAC address in OTP 00:00:00:00:00:00
Net:   No ethernet found.
Hit any key to stop autoboot:  0
Saving Environment to MMC... Writing to redundant MMC(1)... OK
switch to partitions #0, OK
mmc1(part 0) is current device

MMC read: dev # 1, block # 6144, count 4096 ... 4096 blocks read: OK
## Booting kernel from Legacy Image at c0100000 ...
   Image Name:   liteos-a
   Created:      2022-07-27  14:40:30 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1294336 Bytes = 1.2 MiB
   Load Address: c0100000
   Entry Point:  c0100000
   Verifying Checksum ... OK
   Loading Kernel Image

Starting kernel ...

******************Welcome******************

Processor   : Cortex-A7 * 2
Run Mode    : SMP
GIC Rev     : GICv2
build time  : Jul 27 2022 22:36:19
Kernel      : Huawei LiteOS 2.0.0.37/debug

*******************************************

main core booting up...
cpu 0 entering scheduler
cpu 1 entering scheduler
dev random init ...
mem dev init ...
Date:Jul 27 2022.
Time:22:36:03.
DeviceManagerStart start ...
GpioDriverInit: Enterhilog ringbuffer full, drop 9 ▒After PLATFORM_UART ...
cat log shell end
[ERR][Init:thread0][VFS]lookup failed, invalid path err = -22

```

**【恢复手段】：**
无法恢复

**【出现概率】：问题出现次数/实际测试次数**
必现

**【定位信息】：**

- 1. Log、截图、多媒体文件等，所有和问题有关的信息：

OpenHarmony/vendor_bearpi

内容风险标识

评论 (5)

OpenHarmony/vendor_bearpi .gitee-modal { width: 500px !important; }

内容风险标识